IPTV Streaming – Final Guide
A lot of people in the US pay around $99 per month for their cable bill. That’s super expensive and it’s a rise of around 8% when compared to 2010. This is something you pay alongside your already expensive internet and phone bills. You have to focus on finding a solution that will help you stay away from spending a lot of money like that. Thankfully, IPTV is very popular right now just because it makes it easier to eliminate these expenses and focus on the stuff that you like without that much of a hassle.
What is IPTV
Also known as the internet protocol television, this is a service that allows you to watch TV through the internet. You will have to use either your LAN or the internet instead of dealing with satellite signal. As long as you have an internet connection, you can use IPTV, and the best part is that you can access a lot more content and the prices are quite low. It offers you the features and (more…)
Our IPTV service works on MAG boxes with MAC address registeration. Here is how:
Step 1. Firstly, to settings, then system settings in the “inner portal”.
Step 2. Navigate to “software update”, press OK, and then “red button” to update the box’s software. Be patient when the box will restart.
Step 3. Go to Servers/General and write pool.ntp.org and press OK. Go back.
Step 4. Navigate to Portals and on Portal 1 , set it up with this information:
Portal name: Upmaker
Portal URL: http://iptv.#####.com:8080/c/
Step 5. Press OK to save (You can go to Advanced settings to change the time zone of the EPG, if this is necessary)
Step 6. Reboot your device and you can watch the channels if you have sent your MAC address to Upmaker support to register into the servers when ordering a subscription.
Step 7. Enjoy 😉
A Short Primer to CCcam Server & Cardsharing
One of the best ways of catching your favorite TV programs and other TV contents is through CCcam and Card-sharing. You can watch them in real time as it happens whenever and wherever in the world they are broadcast from.
Europe and Globe
we support all European countries and all countries across the globe. For regular individuals like you and me, the mention of the methods in doing this is intimidating. It would sound as if one should possess a thorough technical knowledge of electronics and must be a complete computer expert.
To cut through the gobbledygook of highfaluting technical language, CCcam and Card-Sharing is simply a system wherein many clients (TV receivers) are allowed to have access to a subscription network with only one valid subscription card.
This is done through the electronic sharing of the subscription card’s data by all the sharers. This enables all the sharing clients to have the same-time access to the scrambled DVB streams (the many signals from the subscribed TV networks) which comes encrypted. (If the access is successful, the contents are available for viewing.)
CCcam is the server that controls the operations. Card-sharing, which is self-explanatory, means one subscription card is used and shared by many users.
This technical innovation definitely has benefits to its users, the card sharers. Consider this scenario.
You are flipping the many channels on your TV. You passed by several channels which you have heard about or may have known their contents. Yet, unfortunately, you cannot open and see their contents because they are all locked.
Locked here means these channels are encrypted and are not available for you to view. Your regular satellite dish receiver can only show you your paid-for channels. You cannot unlock (decrypt) the other channels that are closed without paying.
First, your system is not designed to support card-sharing. Second, it is unable to run the software for CCcam protocol.
However, there are now ways to connect your TV system to your chosen CCcam server.
There are now satellite receivers that are capable of card-sharing and are sold everywhere online. One popular choice is Dreambox, a Linux-based receiver. Installation of both hardware and software are not that difficult even for beginners.
The steps are varied, though (hook up to PC, insert smart card, download, install CCcam software, configure, and run to connect to CCcam server).
CCcam server, on the other hand, is a protocol that gives access to digital packages (these are the contents of the channels) where the server is connected to the Internet. It works by transferring the encrypted channel signal codes to a network of computers.
Your computer talks to the server which will then send you the decrypted channel codes. This will then give you access to the TV channels not available to you before. The CCcam server also makes it possible to have other subscribers share the same information (the previously unavailable actual channel contents).
The number of available channels depends on where you live, the size of your satellite dish and where it is pointed at.
This service had been actually intended for users who are in countries that don’t have provider representatives and do not have the opportunity of buying subscription to the package they desire.
How the system works
The first requirement is that card-sharing receivers should be able to communicate over a network that is properly configured. It starts with a device that will confirm where the smart card is. Those without the smart card are satellite card-sharing clients.
Another name for card-sharing is control word sharing. This is the method of having many clients (TV receivers) being able to access a TV network on subscription using just one valid card.
The control words for the system is short and small it is easy to deliver to all the different clients through their Internet connection at home. This had triggered the birth of many sharing network groups where users share their subscription cards with the others in the group.
With it, they are also able to receive the channels they want which the user’s card can decrypt as if that user controls and owns every subscription card that is network-connected. There were other networks as well that were created where the server has many legitimate cards connected to it.
This is done through the electronic sharing a part of the valid conditional output data of the smart card. In turn, this enables all the clients (recipients) to have simultaneous access to the scrambled DVB streams which are held in the TV network which is encrypted.
Typically, this smart card should be legitimate and must be attached to the host television receiver which has to be digital. Moreover, it must be equipped with software to be able to share the decrypted 64-bit “control word” key over a network like the Internet, for instance.
Once the client gets this key, it is now possible to decrypt the content (which is encrypted) as if they are using their own card.
There are some necessary components needed to start your card-sharing server. This includes the network-based hardware like the Dreambox CCcam receiver. Like a regular Ethernet, these receivers must have an Ethernet connection.
Likewise, these must typically use computer software and other plug-ins that are configured to send and receive codes. The software includes Mgcamd, Newcamd, CCcam, Oscam and Wicard emulators. All of these must support CCcam protocol.
The CCcam server also needs a broadband service. It is not possible to use the CCcam server without a broadband service. The server enables you to get the best stations there are.
The best cardsharing server
These days, getting the best TV contents are now attainable by way of finding the best CCcam and card-sharing server that suits your needs. You can now have the best choice of satellite TV packages to servers that are known for their reliability and steady connections.
The reliability of your server’s steady connections means you shall be enjoying from now on your favorite programs without interruptions, drop-outs and other usual glitches associated with common receptions.
OUR Conclusion – AB-Com AB IP Box 250S review
It is not for your novice, if however you just involve some IT knowhow a great bargain , from cccam perspective if you had any problem during cccam installation , please read our tutorial section or contact us .
AB-Com AB IP Box 250S review
The IP Box 250S, from Slovakian satellite wholesaler / retailer / store AB-Com, joins the growing range of set-top boxes to think about outdoors-source Linux operating-system – rather than proprietary internal operating software (‘firmware’).
The main advantage of selecting Linux (which is cute puffin emblem) is always that you’re forget about restricted to the producer for your firmware updates that fix bugs or add more features. Enthusiasts with understanding in the product’s hardware design and limitations possess the source code and modify or rewrite it to reflect their requirements. These, generally, coincide while using ‘wish-lists’ of other clients.
Connected with pension transfer Linux-based boxes, it’s a PVR design – our review sample was outfitted by getting an 80GB ATA/IDE hard disk drive, but we view 400GB models for sale (it’s, incidentally, easy to install and initialise a bigger drive in case you outgrow an 80GB model).
Which boosts a substantial advantage the IP Box 250S has inside the competition – cost. The 80GB version costs around £160 – that can take it near the selling cost from the ordinary budget satellite PVR. But you’ll find caveats.
Most clearly, the IP Box 250S only consists of just one tuner, so recording one funnel as you are watching this option strictly forbidden (sadly, even when they’re on one transponder). Just like a single-tuner design, the 250S is outfitted with simply one LNB input, that’s combined having a loopthrough output for driving slave receivers.
AB-Com AB IP Box 250S review
You’ll find Scarts for TV (RGB/component/S-video/composite) and VCR (composite-only), plus phono electrical electrical sockets for stereo audio and composite video. Digital audio is catered for by an optical TOSlink output. Really the only other connectors will be the all-important Ethernet, plus an RS232 port for upgrading firmware the standard way.
El born area is mid-sized in addition to humble design. Furthermore with a four-digit Introduced display certainly are a standby button exactly the same shape like a horseshoe and a variety of buttons for funnel selection, volume and menu access.
There isn’t any pull-lower flaps and, consequently, no hidden goodies like usb port place or CI slots. However again, would you like the 2nd just in case your receiver is able to do emulating CAMs anyway? Rather, the 250S gives you a card slot for use with whatever CAM your best firmware is emulating, that’s possibly more useful.
To have the ability to maximise the free internal volume, the traditional 3.5in ATA hard disk drive is attached to the top lid. One cannot fault the comfort in the internal construction, that’s tidy.
Furthermore for the primary board (with different ST Microelectronics tuner and embedded 350MIPS PowerPC processor) can be a switch-mode power that’s also capable of supporting hard disk. Whatever the high-ant hardware density, the 250S doesn’t run inside a temperature that gives reason to worry.
AB-Com AB IP Box 250S review
The remote handset is very nondescript to check out and includes buttons that nothing. Round the plus side, it’s acceptably organised in addition to control many TVs. You’ll find, however, some specific firmware-related oddities. While using pre-installed Enigma, the record button didn’t work. Combined with the official IP Box firmware, pressing teletext introduced within the DiSEqC designs for reasons uknown.
Review unit was supplied by getting an earlier ‘port’ in the Enigma firmware, that is familiar to Dreambox clients. It had been provided rather than the ‘official’ AB-Com firmware which, alas, doesn’t provide the onboard card-visitors – certainly within the original incarnation.
After connecting in the 250S with a broadbanded home network and enabling DHCP network auto-configuration within the setup menu (inside the situation of Enigma, one of several in the ‘carousel’ including PVR playback, Television and radio modes), we’re able to upgrade the firmware from a web-based FTP site which were pre-designed to the unit.
There has been two more recent versions – the initial up-to-date without problem, nevertheless the second was hurdled having a CRC error and therefore i wasn’t in a position to proceed further.
Sadly, this Enigma version left a great be preferred. It well-socialized erratically when selecting channels, wouldn’t permit you to start recording by pressing the remote’s ‘record’ button, needed half-hour to complete searching in the Astra 1x cluster and not successful to operate a vehicle a DiSEqC dish properly.
DCM acknowledged that 250S firmwares have handled to maneuver on ever since then, and pointed us with other people who better reflect the capabilities in the unit. They might be directly moved from FTP sites, provided the ‘network update’ designs are completed while using relevant parameters. As an alternative, they might be downloaded from various websites with a PC, and moved for the box.
A freely downloadable program referred to as ‘PCEditor’ is involved. This could also support and modify funnel/satellite databases.
Only then do we installed the state firmware, downloaded within the AB-Com website. It features a menu-driven interface of conventional design the look and feel of the numerous firmwares can differ, however, many styles are normal throughout. Setup parameters (aside from network designs) are the usual – TV standard, aspect ratio, parental control, LNB type, and so on.
Getting used, configuring satellites and finding channels involves a process that’s the identical on a vacation (non-Linux) receiver. Searching manually by individual transponder (frequency, polarity and symbol rate – inside the related ‘advanced’ mode, PIDs can also be specified).
Generally, signal strength and quality bars are displayed. To date because the ‘automatic’ alternative is anxious, searching by file file encryption status and network status are usually supported. Just what a shame there’s no blind search – this can be rarely seen nowadays.
Multi-satellite searches may also be possible, provided you’re employing a motorised dish and possess push the button properly. Here, the dish moves sequentially in a single satellite to a different until all of the available channels have been located.
AB-Com AB IP Box 250S review
Speaking which, the DiSEqC capabilities support Goto-X (USALS/1.3). What’s particularly awesome – certainly with Enigma – is that you could save with a specific DiSEqC memory location (‘satellite number’), therefore making sure compatibility by getting a current DiSEqC receiver’s database.
Sadly, no chance while using ‘official’ firmware and, indeed, a couple of from the third-party ones (a few of which are very similar with regards to look and feel). These need re-install every satellite.
Pressing the ‘enter’ button shows the funnel list, which can be sorted by satellite, file file encryption status or alphabetically. As they are usual, there’s a passionate handset button for switching between television and radio modes.
It is also simple to copy frequently-seen channels into among five pre-designed favourites lists (more such lists might be defined if required). The funnel list also permits channels to get erased or PIN-protected.
Full teletext is supported, as well as the EPG – that tracks might be scheduled – draws in seven-day records, should there be any. These tracks are listed, with particulars for instance EPG-derived programme name/particulars, time/date and funnel, in the ‘file list management’ menu. Separate lists are provided for television and radio tracks.
A variety of handset buttons is provided for playback manipulation – cue, review and pause, for example. The identical controls are suitable for purchase to ‘timeshifting’, because of the receiver’s capacity to buffer the presently up-to-date funnel towards the hard disc.
Presently, though, there’s not a way of saving the products within the buffer should you want to retain them just like a permanent recording. Nor is it possible to edit tracks (beyond renaming, getting rid of or ‘locking’ them). But we’re sure such features may be added through firmware – such could be the power and flexibility in the Linux concept.
You’ll be able to generate a FTP (File Transfer Protocol) session while using box – in the event you navigate your path for the /var/media/video directory, you’ll find all of your tracks. These could be gone to live in some PC for editing, conversion to DVD or storage around the home media server.
The tracks do not take the kind of an average transport stream, and should not thus be processed by utilities like the excellent free software application demultiplexer ProjectX. Thankfully, another free software application program downloadable on the internet, MakePS, will convert these files into standard MPEG ones.
The 250S is able to do an excellent standard of audio-visual performance – certainly from channels that may handle delivering it from consumers. Dynamic range, presentation of detail and colour fidelity all impress.
Appear quality, as proven having a give consideration to some couple of from the better-quality r / c, may also be good. Sensitivity, meanwhile, provides pointless to worry. A 1m motorised dish with .7dB LNB introduced in channels from numerous satellites, including Hot Bird, Astras 1x and 2x, Thor and Sirius.
We attempted a number of firmwares (official and unofficial) and searching out was, alas, equally slow generally. A whole scan of Hot Bird’s 100 roughly transponders, for example, needed between 10 and 15 minutes.
Thankfully, everyday funnel selection is a lot more responsive. If you’re carrying out a multi-satellite scan, an irritating problem becomes apparent. It starts checking before the dish has stopped moving – therefore the satellite’s initial few transponders might be skipped. The most recent official software wasn’t without its problems.
Periodically, it could display ‘error’ round the front panel display, and shut itself lower. Ironically, the unofficial ones shown more reliable in this manner!
However, it must be appreciated the 250S can be a be employed in progress. It is not in the marketplace for extended and will also be considered a while before the designers are fully current using this intriguing receiver. Similar encounters were reported previously in the Dreambox range.
If you are in a position to think that the odd feature might not function correctly within the start, your IP Box 250S provides extensive choosing it.
Features are restricted only with the desires and points of interest of people writing firmware and plug-ins with this – but to this day the 250S are capable of doing an infinitely more than non-Linux PVRs of comparable cost.
If you’re a satellite enthusiast from it experience (Linux clients will need for the 250S as being a duck to water) then consider the 250S as something from the bargain.
Also , You may install CCcam server on this device , if You had any problem during installation please do not hesitate to contact us .
Update: We Don’t Accept PaySafeCard Payments For now, But You can Pay with Paypal And Credit Card .
Your Paysafe code can not be traced, contact us and we tell you what to do. You get Paysafe cards at gas stations, drugstores and supermarkets and newsagents.
Can my Paysafe code be traced after purchase CardSharing?
Are indicators of failed messages from your receiver such. As tuning, SID not found in PAT and many more.
Furthermore, you also see this because if your BER is high and where applicable, your SNR value is too low.
– Bring a realignment of your satellite system
– For cable users a receiver amplifier recommended here (cost about 25 euros in the electronics market)
– A channel scan
– A completely new channel list
If you have further questions, we will help you.
How do I determine if I have problems with reception?
We offer all Sky packages are included incl. The new Bundesliga and sports HD channels.
Which Sky packages are included in your offer?
Yes, of course the Bundesliga and sports HD channels are included.
Are the Bundesliga and the sport of Sky HD channels contain?